AS ONE首页 >
测量/测定/检查 >
物性/物理量测定仪器 的结果:29条 小分类有 1 种 (如果显示出来的搜索结果过多,可以通过以下小分类筛选您要的产品种类)
更多参数()
收起
-
64-0697-99 共有1种
适用于DOS V FGC FGPXRS 232 C缆线
¥1,140.00起
参考单价¥1,140.00起
-
64-0697-98 共有1种
模拟电缆FGC FGPX FGP
¥715.00起
参考单价¥715.00起
-
64-0697-68 共有1种
AC适配器(FGP用)
¥275.00起
参考单价¥275.00起
-
64-0698-68 共有4种
数显测力计(带证书)
咨询
-
64-0698-04 共有1种
齿轮传感器
¥2,000.00起
参考单价¥2,000.00起
-
64-0698-16 共有4种
扭矩仪 支持USB TNX系列
¥48,000.00起
参考单价¥48,000.00起
-
64-0697-90 共有2种
数显式测力仪/支架
¥33,300.00起
参考单价¥33,300.00起
-
64-0697-58 共有1种
AC适配器(FGN用)
¥275.00起
参考单价¥275.00起
-
64-0697-81 共有9种
单柱拉力试验机
咨询
-
64-0698-08 共有1种
闪光灯用氙气灯 附带治具 KDTB3100661**
¥1,050.00起
参考单价¥1,050.00起
-
64-0698-72 共有9种
数字测力计(带证书)
咨询
-
64-0697-69 共有9种
数字测力仪
¥13,000.00起
参考单价¥13,000.00起
-
64-0698-88 共有2种
数字式推拉力计
咨询
-
64-0698-92 共有3种
带开栓扭矩仪/制造商校准证书+可追溯体系图 TNJ系列
咨询
-
64-0697-93 共有2种
数显式测力仪/支架
¥6,340.00起
参考单价¥6,340.00起
-
64-0697-83 共有2种
立式测力仪专用电动支架
咨询
-
64-0697-59 共有8种
数显推拉力计
¥8,510.00起
参考单价¥8,510.00起
-
64-0696-99 共有1种
电动扭矩测量仪
¥56,700.00起
参考单价¥56,700.00起
-
64-0698-09 共有3种
开栓扭矩仪 TNJ系列
¥20,100.00起
参考单价¥20,100.00起
-
64-0697-76 共有2种
数字测力仪
¥21,100.00起
参考单价¥21,100.00起
-
64-0697-97 共有1种
小型台式试验机主机
咨询
-
64-0698-12 共有3种
开栓扭矩仪 带USB输出 TNP系列
¥24,000.00起
参考单价¥24,000.00起
-
64-0697-92 共有1种
手动载物台
¥10,900.00起
参考单价¥10,900.00起
-
64-0697-80 共有1种
AC适配器(FGPX用)
¥275.00起
参考单价¥275.00起
-
64-0698-20 共有1种
AC适配器(TNX用)
¥1,020.00起
参考单价¥1,020.00起
-
64-0698-81 共有9种
数显式测力仪(带证书)
咨询
-
64-0698-95 共有4种
带开栓扭矩仪(带USB输出)/制造商校准证书+可追溯体系图 TNP系
咨询
-
64-0697-54 共有4种
数显推拉力计
¥5,270.00起
参考单价¥5,270.00起
-
64-0698-99 共有4种
带扭矩仪(支持USB)/制造商校准证书+可追溯体系图 TNX系列
咨询
-
¥1,140.00起 参考单价¥1,140.00起
查看详情 >
编号 | 型号 | 销售包装 | RMB(含税) | 北京库存 | 上海库存 | 日本库存 | 参考货期 | 查询NO. |
64-0697-99 | FGTC-6006 | 1个 | 1,140.00 | 0 | 0 | 0 | 25天左右 | **21 |
-
编号 | 型号 | 销售包装 | RMB(含税) | 北京库存 | 上海库存 | 日本库存 | 参考货期 | 查询NO. |
64-0697-98 | FGTC-6001 | 1个 | 715.00 | 0 | 0 | 0 | 25天左右 | **21 |
-
编号 | 型号 | 销售包装 | RMB(含税) | 北京库存 | 上海库存 | 日本库存 | 参考货期 | 查询NO. |
64-0697-68 | 6A-061WU09-021 | 1个 | 275.00 | 0 | 0 | 0 | 23天左右 | **2Z |
-
编号 | 型号 | 额定容量(R.C.) | 可见范围 | 显示分辨率 | 销售包装 | RMB(含税) | 北京库存 | 上海库存 | 日本库存 | 参考货期 | 查询NO. |
64-0698-68 | FGJN-2 | ±20.00N(±2.000kg) | ±20.00N±2.000kg | 0.01N/0.001kg | 1台 | 咨询 | 0 | 0 | 0 | 45天左右 | **20 |
64-0698-69 | FGJN-20 | ±200.0N(±20.00kg) | ±200.0N±20.00kg | 0.1N/0.01kg | 1台 | 咨询 | 0 | 0 | 0 | 45天左右 | **20 |
64-0698-70 | FGJN-5 | ±50.00N(±5.000kg) | ±50.00N±5.000kg | 0.01N/0.001kg | 1台 | 咨询 | 0 | 0 | 0 | 45天左右 | **20 |
64-0698-71 | FGJN-50 | ±500.0N(±50.00kg) | ±500.0N±50.00kg | 0.1N/0.01kg | 1台 | 咨询 | 0 | 0 | 0 | 45天左右 | **20 |
-
¥2,000.00起 参考单价¥2,000.00起
查看详情 >
编号 | 型号 | 销售包装 | RMB(含税) | 北京库存 | 上海库存 | 日本库存 | 参考货期 | 查询NO. |
64-0698-04 | SE-G2 | 1个 | 2,000.00 | 0 | 0 | 0 | 22天左右 | **21 |
-
¥48,000.00起 参考单价¥48,000.00起
查看详情 >
编号 | 型号 | 定格トルク | 計測範囲 | 計測単位 | 表示範囲 | 表示分解能 | 销售包装 | RMB(含税) | 北京库存 | 上海库存 | 日本库存 | 参考货期 | 查询NO. |
64-0698-16 | TNX-0.5 | 500mN・m(0.5N・m) | 0.0~±500.0mN・m | mN・m、N・cmより切換 | 0.0~±500.0mN・m、0.00~±50.00N・cm | 0.1mN・m、0.01N・cm | 1台 | 48,000.00 | 0 | 0 | 0 | 22天左右 | **21 |
64-0698-17 | TNX-10 | 10N・m | 0.00~±10.00N・m | mN・m、N・cmより切換 | 0.00~±10.00N・m 0~±1000N・cm | 0.01N・m 1N・cm | 1台 | 48,000.00 | 0 | 0 | 0 | 22天左右 | **21 |
64-0698-18 | TNX-2 | 2N・m | 0.000~±2.000N・m | N・m、N・cmより切換 | 0.000~±2.000N・m 0.0~±200.0N・cm | 0.001N・m 0.1N・cm | 1台 | 48,000.00 | 0 | 0 | 0 | 22天左右 | **21 |
64-0698-19 | TNX-5 | 5N・m | 0.000~±5.000N・m | mN・m、N・cmより切換 | 0.000~±5.000N・m 0.0~±500.0N・cm | 0.1mN・m、0.01N・cm | 1台 | 48,000.00 | 0 | 0 | 0 | 22天左右 | **21 |
-
¥33,300.00起 参考单价¥33,300.00起
查看详情 >
编号 | 型号 | 进给速度 | 移动速度 | 销售包装 | RMB(含税) | 北京库存 | 上海库存 | 日本库存 | 参考货期 | 查询NO. |
64-0697-90 | FGS-50E-H | 20-600mm/min | 20-600mm/min | 1台 | 33,300.00 | 0 | 0 | 0 | 23天左右 | **21 |
64-0697-91 | FGS-50E-L | 6-180mm/min | 6-180mm/min | 1台 | 33,300.00 | 0 | 0 | 0 | 25天左右 | **21 |
-
编号 | 型号 | 销售包装 | RMB(含税) | 北京库存 | 上海库存 | 日本库存 | 参考货期 | 查询NO. |
64-0697-58 | 6A-061WU09-021 | 1个 | 275.00 | 0 | 0 | 0 | 23天左右 | **2Z |
-
编号 | 型号 | 测量载荷 | 销售包装 | RMB(含税) | 北京库存 | 上海库存 | 日本库存 | 参考货期 | 查询NO. |
64-0697-81 | FGS-1000TV | 1000N | 1台 | 咨询 | 0 | 0 | 0 | 22天左右 | **20 |
64-0697-82 | FGS-100TV | 100N | 1台 | 咨询 | 0 | 0 | 0 | 22天左右 | **20 |
64-0697-84 | FGS-10TV | 10N | 1台 | 咨询 | 0 | 0 | 0 | 22天左右 | **20 |
64-0697-85 | FGS-200TV | 200N | 1台 | 咨询 | 0 | 0 | 0 | 22天左右 | **20 |
64-0697-86 | FGS-20TV | 20N | 1台 | 咨询 | 0 | 0 | 0 | 22天左右 | **20 |
64-0697-88 | FGS-2TV | 2N | 1台 | 咨询 | 0 | 0 | 0 | 22天左右 | **20 |
64-0697-89 | FGS-500TV | 500N | 1台 | 咨询 | 0 | 0 | 0 | 22天左右 | **20 |
64-0697-94 | FGS-50TV | 50N | 1台 | 咨询 | 0 | 0 | 0 | 22天左右 | **20 |
64-0697-96 | FGS-5TV | 5N | 1台 | 咨询 | 0 | 0 | 0 | 22天左右 | **20 |
-
¥1,050.00起 参考单价¥1,050.00起
查看详情 >
编号 | 型号 | 销售包装 | RMB(含税) | 北京库存 | 上海库存 | 日本库存 | 参考货期 | 查询NO. |
64-0698-08 | TFU-102B ASSY | 1个 | 1,050.00 | 0 | 0 | 0 | 22天左右 | **21 |
-
编号 | 型号 | 额定容量(R.C.) | 可见范围 | 温度影响 | 过载耐量 | 重量 | 销售包装 | RMB(含税) | 北京库存 | 上海库存 | 日本库存 | 参考货期 | 查询NO. |
64-0698-72 | FGP-0.2 | ±2.000N(±200.0g) | ±2.000N±200.0g | 增益±0.01%LOAD/°C、零点±0.01%/R.C./°C(零点漂移可通过跟踪功能消除) | 200%R.C. | 约450g | 1台 | 咨询 | 0 | 0 | 0 | 50天左右 | **20 |
64-0698-73 | FGP-0.5 | ±5.000N(±500.0g) | ±5.000N±500.0g | 增益±0.01%LOAD/°C、零点±0.02%/R.C./°C(零点漂移可通过跟踪功能消除) | 200%R.C. | 约450g | 1台 | 咨询 | 0 | 0 | 0 | 45天左右 | **20 |
64-0698-74 | FGP-1 | ±10.00N(±1000g) | ±10.00N±1000g | 增益±0.01%LOAD/°C、零点±0.03%/R.C./°C(零点漂移可通过跟踪功能消除) | 200%R.C. | 约450g | 1台 | 咨询 | 0 | 0 | 0 | 60天左右 | **20 |
64-0698-75 | FGP-10 | ±100.0N(±10.00kg) | ±100.0N±10.00kg | 增益±0.01%LOAD/°C、零点±0.06%/R.C./°C(零点漂移可通过跟踪功能消除) | 200%R.C. | 约450g | 1台 | 咨询 | 0 | 0 | 0 | 45天左右 | **20 |
64-0698-76 | FGP-100 | ±1000N(±100.0kg) | ±1000N±100.0kg | 增益±0.01%LOAD/°C、零点±0.09%/R.C./°C(零点漂移可通过跟踪功能消除) | 150%R.C. | 约500g | 1台 | 咨询 | 0 | 0 | 0 | 45天左右 | **20 |
64-0698-77 | FGP-2 | ±20.00N(±2.000kg) | ±20.00N±2.000kg | 增益±0.01%LOAD/°C、零点±0.04%/R.C./°C(零点漂移可通过跟踪功能消除) | 200%R.C. | 约450g | 1台 | 咨询 | 0 | 0 | 0 | 45天左右 | **20 |
64-0698-78 | FGP-20 | ±200.0N(±20.00kg) | ±200.0N±20.00kg | 增益±0.01%LOAD/°C、零点±0.07%/R.C./°C(零点漂移可通过跟踪功能消除) | 200%R.C. | 约450g | 1台 | 咨询 | 0 | 0 | 0 | 45天左右 | **20 |
64-0698-79 | FGP-5 | ±50.00N(±5.000kg) | ±50.00N±5.000kg | 增益±0.01%LOAD/°C、零点±0.05%/R.C./°C(零点漂移可通过跟踪功能消除) | 200%R.C. | 约450g | 1台 | 咨询 | 0 | 0 | 0 | 45天左右 | **20 |
64-0698-80 | FGP-50 | ±500.0N(±50.00kg) | ±500.0N±50..00kg | 增益±0.01%LOAD/°C、零点±0.08%/R.C./°C(零点漂移可通过跟踪功能消除) | 200%R.C. | 约450g | 1台 | 咨询 | 0 | 0 | 0 | 45天左右 | **20 |
-
¥13,000.00起 参考单价¥13,000.00起
查看详情 >
编号 | 型号 | 额定容量(R.C.) | 可见范围 | 显示分辨率 | 过载耐量 | 尺寸 | 销售包装 | RMB(含税) | 北京库存 | 上海库存 | 日本库存 | 参考货期 | 查询NO. |
64-0697-69 | FGP×-0.2 | ±2.000N(±200.0g) | ±2.000N(±200.0g) | 0.001N/o.1g | 200%R.C软件 | 宽75×厚38×长141mm | 1台 | 13,000.00 | 0 | 0 | 0 | 22天左右 | **21 |
64-0697-70 | FGP×-0.5 | ±5.000N(±500.0g) | ±5.000N(±500.0g) | 0.001N/o.1g | 200%R.C软件 | 宽75×厚38×长141mm | 1台 | 13,000.00 | 0 | 0 | 0 | 22天左右 | **21 |
64-0697-71 | FGP×-1 | ±10.00N(±1000g) | ±10.00N(±1000g) | 0.01N/1g | 200%R.C软件 | 宽75×厚38×长147mm | 1台 | 13,000.00 | 0 | 0 | 0 | 22天左右 | **21 |
64-0697-72 | FGP×-10 | ±100.0N(±10.00kg) | ±100.0N(±10.00kg) | 0.1N/0.01kg | 200%R.C软件 | 宽75×厚38×长147mm | 1台 | 13,000.00 | 0 | 0 | 0 | 22天左右 | **21 |
64-0697-73 | FGP×-100 | ±1000N(±100.0kg) | ±1000N(±100.0kg) | 1N/0.1kg | 150%R.C软件 | 宽75×厚38×长149mm | 1台 | 20,300.00 | 0 | 0 | 0 | 22天左右 | **21 |
64-0697-74 | FGP×-2 | ±20.00N(±2.000kg) | ±20.00N(±2.000kg) | 0.01N/0.001kg | 200%R.C软件 | 宽75×厚38×长147mm | 1台 | 13,000.00 | 0 | 0 | 0 | 22天左右 | **21 |
64-0697-75 | FGP×-20 | ±200.0N(±20.00kg) | ±200.0N(±20.00kg) | 0.1N/0.01kg | 200%R.C软件 | 宽75×厚38×长147mm | 1台 | 13,000.00 | 0 | 0 | 0 | 22天左右 | **21 |
64-0697-77 | FGP×-5 | ±50.00N(±5.000kg) | ±50.00N(±5.000kg) | 0.01N/0.001kg | 200%R.C软件 | 宽75×厚38×长147mm | 1台 | 13,000.00 | 0 | 0 | 0 | 22天左右 | **21 |
64-0697-78 | FGP×-50 | ±500.0N(±50.00kg) | ±500.0N(±50.00kg) | 0.1N/0.01kg | 200%R.C软件 | 宽75×厚38×长147mm | 1台 | 13,000.00 | 0 | 0 | 0 | 25天左右 | **21 |
-
编号 | 型号 | 额定容量(R.C.) | 可见范围 | 重量 | 显示分辨率 | 销售包装 | RMB(含税) | 北京库存 | 上海库存 | 日本库存 | 参考货期 | 查询NO. |
64-0698-88 | FGP×-250H | ±2500N(±250kg) | ±2500N±250.0kg | 约900g | 1N/0.1kg软 | 1台 | 咨询 | 0 | 0 | 0 | 45天左右 | **20 |
64-0698-91 | FGP×-500H | ±5000N(±500kg) | ±5000N±500.0kg软 | 约1000g | - | 1台 | 咨询 | 0 | 0 | 0 | 45天左右 | **20 |
-
编号 | 型号 | 計測トルク | 計測範囲 | 重量 | 销售包装 | RMB(含税) | 北京库存 | 上海库存 | 日本库存 | 参考货期 | 查询NO. |
64-0698-92 | TNJ-10 | 10N・m | ±10.00N・m ±1000N・cm | 12.5kg | 1台 | 咨询 | 0 | 0 | 0 | 45天左右 | **20 |
64-0698-93 | TNJ-2 | 2N・m | ±2.000N・m ±200.0N・cm | 8kg | 1台 | 咨询 | 0 | 0 | 0 | 45天左右 | **20 |
64-0698-94 | TNJ-5 | 5N・m | ±5.000N・m ±500.0N・cm | 8kg | 1台 | 咨询 | 0 | 0 | 0 | 50天左右 | **20 |
-
¥6,340.00起 参考单价¥6,340.00起
查看详情 >
编号 | 型号 | 销售包装 | RMB(含税) | 北京库存 | 上海库存 | 日本库存 | 参考货期 | 查询NO. |
64-0697-93 | FGS-50L | 1台 | 8,020.00 | 0 | 0 | 0 | 22天左右 | **21 |
64-0697-95 | FGS-5S | 1台 | 6,340.00 | 0 | 0 | 0 | 25天左右 | **21 |
-
编号 | 型号 | 测量载荷 | 耐负荷 | 重量 | 销售包装 | RMB(含税) | 北京库存 | 上海库存 | 日本库存 | 参考货期 | 查询NO. |
64-0697-83 | FGS-100VC | 1000N(100kgf) | 1000N(100kgf) | 约63kg | 1台 | 咨询 | 0 | 0 | 0 | 22天左右 | **20 |
64-0697-87 | FGS-250VC | 2500N(250kgf) | 2500N(250kgf) | 约65kg | 1台 | 咨询 | 0 | 0 | 0 | 22天左右 | **20 |
-
¥8,510.00起 参考单价¥8,510.00起
查看详情 >
编号 | 型号 | 额定容量(R.C.) | 可见范围 | 温度影响 | 过载耐量 | 重量(g) | 销售包装 | RMB(含税) | 北京库存 | 上海库存 | 日本库存 | 参考货期 | 查询NO. |
64-0697-59 | FGP-0.2 | ±2.000N(±200.0g) | ±2.000N±200.0g | 增益±0.01%LOAD/°C、零点±0.01%/R.C./°C(零点漂移可通过跟踪功能消除) | 200%R.C. | 约450 | 1台 | 8,510.00 | 0 | 0 | 0 | 23天左右 | **21 |
64-0697-60 | FGP-0.5 | ±5.000N(±500.0g) | ±5.000N±500.0g | 增益±0.01%LOAD/°C、零点±0.02%/R.C./°C(零点漂移可通过跟踪功能消除) | 200%R.C. | 约450 | 1台 | 8,510.00 | 0 | 0 | 0 | 23天左右 | **21 |
64-0697-61 | FGP-1 | ±10.00N(±1000g) | ±10.00N±1000g | 增益±0.01%LOAD/°C、零点±0.03%/R.C./°C(零点漂移可通过跟踪功能消除) | 200%R.C. | 约450 | 1台 | 8,510.00 | 0 | 0 | 0 | 23天左右 | **21 |
64-0697-62 | FGP-10 | ±100.0N(±10.00kg) | ±100.0N±10.00kg | 增益±0.01%LOAD/°C、零点±0.06%/R.C./°C(零点漂移可通过跟踪功能消除) | 200%R.C. | 约450 | 1台 | 8,510.00 | 0 | 0 | 0 | 23天左右 | **21 |
64-0697-63 | FGP-100 | ±1000N(±100.0kg) | ±1000N±100.0kg | 增益±0.01%LOAD/°C、零点±0.09%/R.C./°C(零点漂移可通过跟踪功能消除) | 150%R.C. | 约450 | 1台 | 15,900.00 | 0 | 0 | 0 | 23天左右 | **21 |
64-0697-64 | FGP-2 | ±20.00N(±2.000kg) | ±20.00N±2.000kg | 增益±0.01%LOAD/°C、零点±0.04%/R.C./°C(零点漂移可通过跟踪功能消除) | 200%R.C. | 约450 | 1台 | 8,510.00 | 0 | 0 | 0 | 22天左右 | **21 |
64-0697-65 | FGP-20 | ±200.0N(±20.00kg) | ±200.0N±20.00kg | 增益±0.01%LOAD/°C、零点±0.07%/R.C./°C(零点漂移可通过跟踪功能消除) | 200%R.C. | 约450 | 1台 | 8,510.00 | 0 | 0 | 0 | 22天左右 | **21 |
64-0697-67 | FGP-50 | ±500.0N(±50.00kg) | ±500.0N±50..00kg | 增益±0.01%LOAD/°C、零点±0.08%/R.C./°C(零点漂移可通过跟踪功能消除) | 200%R.C. | 约450 | 1台 | 8,510.00 | 0 | 0 | 0 | 23天左右 | **21 |
-
¥56,700.00起 参考单价¥56,700.00起
查看详情 >
编号 | 型号 | 销售包装 | RMB(含税) | 北京库存 | 上海库存 | 日本库存 | 参考货期 | 查询NO. |
64-0696-99 | DSP-5E | 1个 | 56,700.00 | 0 | 0 | 0 | 22天左右 | **21 |
-
¥20,100.00起 参考单价¥20,100.00起
查看详情 >
编号 | 型号 | 計測トルク | 計測範囲 | 重量 | 销售包装 | RMB(含税) | 北京库存 | 上海库存 | 日本库存 | 参考货期 | 查询NO. |
64-0698-09 | TNJ-10 | 10N・m | ±10.00N・m ±1000N・cm | 12.5kg | 1台 | 20,100.00 | 0 | 0 | 0 | 23天左右 | **21 |
64-0698-10 | TNJ-2 | 2N・m | ±2.000N・m ±200.0N・cm | 8kg | 1台 | 20,100.00 | 0 | 0 | 0 | 22天左右 | **21 |
64-0698-11 | TNJ-5 | 5N・m | ±5.000N・m ±500.0N・cm | 8kg | 1台 | 20,100.00 | 0 | 0 | 0 | 23天左右 | **21 |
-
¥21,100.00起 参考单价¥21,100.00起
查看详情 >
编号 | 型号 | 额定容量(R.C.) | 可见范围 | 重量 | 显示分辨率 | 销售包装 | RMB(含税) | 北京库存 | 上海库存 | 日本库存 | 参考货期 | 查询NO. |
64-0697-76 | FGP×-250H | ±2500N(±250kg) | ±2500N±250.0kg | 约900g | 1N/0.1kg | 1台 | 21,100.00 | 0 | 0 | 0 | 34天左右 | **21 |
64-0697-79 | FGP×-500H | ±5000N(±500kg) | ±5000N±500.0kg软 | 约1000g | - | 1台 | 23,700.00 | 0 | 0 | 0 | 22天左右 | **21 |
-
编号 | 型号 | 销售包装 | RMB(含税) | 北京库存 | 上海库存 | 日本库存 | 参考货期 | 查询NO. |
64-0697-97 | FGS-TV | 1台 | 咨询 | 0 | 0 | 0 | 22天左右 | **20 |
-
¥24,000.00起 参考单价¥24,000.00起
查看详情 >
编号 | 型号 | 計測トルク | 計測範囲 | 計測単位 | 重量 | 销售包装 | RMB(含税) | 北京库存 | 上海库存 | 日本库存 | 参考货期 | 查询NO. |
64-0698-12 | TNP-0.5 | 500mN・m(0.5N・m) | 0.0~±500.0mN・m、0.00~±50.00N・cm | mN・m、N・cm | 8kg | 1台 | 24,000.00 | 0 | 0 | 0 | 22天左右 | **21 |
64-0698-13 | TNP-10 | 10N・m | ±10.00N・m ±1000N・cm | N・m、N・cm | 12.5kg | 1台 | 24,000.00 | 0 | 0 | 0 | 22天左右 | **21 |
64-0698-14 | TNP-2 | 2N・m | ±2.000N・m ±200.0N・cm | N・m、N・cm | 8kg | 1台 | 24,000.00 | 0 | 0 | 0 | 22天左右 | **21 |
-
¥10,900.00起 参考单价¥10,900.00起
查看详情 >
编号 | 型号 | 销售包装 | RMB(含税) | 北京库存 | 上海库存 | 日本库存 | 参考货期 | 查询NO. |
64-0697-92 | FGS-50H | 1台 | 10,900.00 | 0 | 0 | 0 | 22天左右 | **21 |
-
编号 | 型号 | 销售包装 | RMB(含税) | 北京库存 | 上海库存 | 日本库存 | 参考货期 | 查询NO. |
64-0697-80 | 6A-061WU09-021 | 1个 | 275.00 | 0 | 0 | 0 | 23天左右 | **2Z |
-
¥1,020.00起 参考单价¥1,020.00起
查看详情 >
编号 | 型号 | 销售包装 | RMB(含税) | 北京库存 | 上海库存 | 日本库存 | 参考货期 | 查询NO. |
64-0698-20 | TNX-AC001 | 1个 | 代替品编号::停止销售 | 0 | 0 | 0 | 另询 | **2Z |
-
编号 | 型号 | 额定容量(R.C.) | 可见范围 | 显示分辨率 | 过载耐量 | 尺寸 | 销售包装 | RMB(含税) | 北京库存 | 上海库存 | 日本库存 | 参考货期 | 查询NO. |
64-0698-81 | FGP×-0.2 | ±2.000N(±200.0g) | ±2.000N(±200.0g) | 0.001N/o.1g | 200%R.C软件 | 宽75×厚38×长141mm | 1台 | 咨询 | 0 | 0 | 0 | 45天左右 | **20 |
64-0698-82 | FGP×-0.5 | ±5.000N(±500.0g) | ±5.000N(±500.0g) | 0.001N/o.1g | 200%R.C软件 | 宽75×厚38×长141mm | 1台 | 咨询 | 0 | 0 | 0 | 45天左右 | **20 |
64-0698-83 | FGP×-1 | ±10.00N(±1000g) | ±10.00N(±1000g) | 0.01N/1g | 200%R.C软件 | 宽75×厚38×长147mm | 1台 | 咨询 | 0 | 0 | 0 | 45天左右 | **20 |
64-0698-84 | FGP×-10 | ±100.0N(±10.00kg) | ±100.0N(±10.00kg) | 0.1N/0.01kg | 200%R.C软件 | 宽75×厚38×长147mm | 1台 | 咨询 | 0 | 0 | 0 | 45天左右 | **20 |
64-0698-85 | FGP×-100 | ±1000N(±100.0kg) | ±1000N(±100.0kg) | 1N/0.1kg | 150%R.C软件 | 宽75×厚38×长149mm | 1台 | 咨询 | 0 | 0 | 0 | 45天左右 | **20 |
64-0698-86 | FGP×-2 | ±20.00N(±2.000kg) | ±20.00N(±2.000kg) | 0.01N/0.001kg | 200%R.C软件 | 宽75×厚38×长147mm | 1台 | 咨询 | 0 | 0 | 0 | 45天左右 | **20 |
64-0698-87 | FGP×-20 | ±200.0N(±20.00kg) | ±200.0N(±20.00kg) | 0.1N/0.01kg | 200%R.C软件 | 宽75×厚38×长147mm | 1台 | 咨询 | 0 | 0 | 0 | 45天左右 | **20 |
64-0698-89 | FGP×-5 | ±50.00N(±5.000kg) | ±50.00N(±5.000kg) | 0.01N/0.001kg | 200%R.C软件 | 宽75×厚38×长147mm | 1台 | 咨询 | 0 | 0 | 0 | 45天左右 | **20 |
64-0698-90 | FGP×-50 | ±500.0N(±50.00kg) | ±500.0N(±50.00kg) | 0.1N/0.01kg | 200%R.C软件 | 宽75×厚38×长147mm | 1台 | 咨询 | 0 | 0 | 0 | 45天左右 | **20 |
-
编号 | 型号 | 計測トルク | 計測範囲 | 計測単位 | メイン表示部 | サブ表示部 | 销售包装 | RMB(含税) | 北京库存 | 上海库存 | 日本库存 | 参考货期 | 查询NO. |
64-0698-95 | TNP-0.5 | 500mN・m(0.5N・m) | 0.0~±500.0mN・m、0.00~±50.00N・cm | mN・m、N・cm | 4桁LCD表示 文字高さ12mm | 3桁LCD表示 文字高さ7mm | 1台 | 咨询 | 0 | 0 | 0 | 45天左右 | **20 |
64-0698-96 | TNP-10 | 10N・m | ±10.00N・m ±1000N・cm | N・m、N・cm | 4桁LCD表示 文字高さ 12mm | 3桁LCD表示 文字高さ 7mm | 1台 | 咨询 | 0 | 0 | 0 | 45天左右 | **20 |
64-0698-97 | TNP-2 | 2N・m | ±2.000N・m ±200.0N・cm | N・m、N・cm | 4桁LCD表示 文字高さ 12mm | 3桁LCD表示 文字高さ 7mm | 1台 | 咨询 | 0 | 0 | 0 | 45天左右 | **20 |
64-0698-98 | TNP-5 | 5N・m | ±5.000N・m ±500.0N・cm | N・m、N・cm | 4桁LCD表示 文字高さ 12mm | 3桁LCD表示 文字高さ 7mm | 1台 | 咨询 | 0 | 0 | 0 | 45天左右 | **20 |
-
¥5,270.00起 参考单价¥5,270.00起
查看详情 >
编号 | 型号 | 额定容量(R.C.) | 可见范围 | 显示分辨率 | 销售包装 | RMB(含税) | 北京库存 | 上海库存 | 日本库存 | 参考货期 | 查询NO. |
64-0697-54 | FGJN-2 | ±20.00N(±2.000kg) | ±20.00N±2.000kg | 0.01N/0.001kg | 1台 | 5,270.00 | 0 | 0 | 0 | 另询 | **21 |
64-0697-55 | FGJN-20 | ±200.0N(±20.00kg) | ±200.0N±20.00kg | 0.1N/0.01kg | 1台 | 5,270.00 | 0 | 0 | 0 | 22天左右 | **21 |
64-0697-56 | FGJN-5 | ±50.00N(±5.000kg) | ±50.00N±5.000kg | 0.01N/0.001kg | 1台 | 5,270.00 | 0 | 0 | 0 | 23天左右 | **21 |
64-0697-57 | FGJN-50 | ±500.0N(±50.00kg) | ±500.0N±50.00kg | 0.1N/0.01kg | 1台 | 5,270.00 | 0 | 0 | 0 | 另询 | **21 |
-
编号 | 型号 | 定格トルク | 計測範囲 | 計測単位 | 表示範囲 | 表示分解能 | 销售包装 | RMB(含税) | 北京库存 | 上海库存 | 日本库存 | 参考货期 | 查询NO. |
64-0698-99 | TNX-0.5 | 500mN・m(0.5N・m) | 0.0~±500.0mN・m | mN・m、N・cmより切換 | 0.0~±500.0mN・m、0.00~±50.00N・cm | 0.1mN・m、0.01N・cm | 1台 | 咨询 | 0 | 0 | 0 | 45天左右 | **20 |
64-0699-01 | TNX-10 | 10N・m | 0.00~±10.00N・m | mN・m、N・cmより切換 | 0.00~±10.00N・m 0~±1000N・cm | 0.01N・m 1N・cm | 1台 | 咨询 | 0 | 0 | 0 | 45天左右 | **20 |
64-0699-02 | TNX-2 | 2N・m | 0.000~±2.000N・m | N・m、N・cmより切換 | 0.000~±2.000N・m 0.0~±200.0N・cm | 0.001N・m 0.1N・cm | 1台 | 咨询 | 0 | 0 | 0 | 45天左右 | **20 |
64-0699-03 | TNX-5 | 5N・m | 0.000~±5.000N・m | mN・m、N・cmより切換 | 0.000~±5.000N・m 0.0~±500.0N・cm | 0.1mN・m、0.01N・cm | 1台 | 咨询 | 0 | 0 | 0 | 45天左右 | **20 |
-
64-0697-99 共有1种
¥1,140.00起
参考单价¥1,140.00起
-
64-0697-98 共有1种
规格:● 自适应型号:FGC系列、FGPX系列、FGP系列
-
64-0697-68 共有1种
-
64-0698-68 共有4种
特点:● 商品本体含有制造商已完成的整套校准证书、测试报告、可溯源性、以及参考设备官方证书。
● 可用于从20.00N(2kg)到500.0N(50kg)的简易试验用测力计系列
● 提高了测量精度,可在1000次/秒的高速下测量峰值。
● 正常测量最多可选择20次/秒。
● 显示周期为1次/秒、2次/秒、3次/秒、5次/秒、10次/秒、20次/秒。
● 采用反转型,可一键将显示数值与显示单位倒置显示。
● 可一键切换N和kg(g)等各单位。
● 可测量峰值
规格:● 单位:N、kg(可上下颠倒显示)
● 计测方式:1.通常计测2.正峰值计测3.负峰值计测
● 显示周期:1次/秒、2次/秒、3次/秒、5次/秒、10次/秒、20次/秒
● 计测时间:1000次/秒
● 精度:额定容量的±0.3%及±1/2digit(在23°C下)
● 温度影响:跟踪处理取消、跨度±0.03%/LOAD/°C
● 显示器:4位液晶显示器,文字高12mm、牵引负荷-显示(可上下颠倒显示)各种显示1"LOBAT"(电池电压下降)2"BAT"(充电中)3"OVR"(过载)4"PEAK"(峰值保持模式)
● 过载耐量:200%/R.C.
● 跟踪功能:有(可ON/OFF切换)
● 电源:充电式(内置镍氢电池)和AC适配器(DC9V200mA),充电中可测量
● 可使用时间:充满电后约8小时
● 充电时间:最长12小时(充满电后自动结束)
● 自动电源关闭功能:10分钟(使用AC适配器时可连续使用)或关闭
● 温度范围:0~40°C
● 尺寸:宽75×厚10×长20mm
● 重量:约1000g(含电池)
● 配件:测量适配器(M6)、吊架、AC适配器、充电中可测量
● 手提箱
-
64-0698-04 共有1种
特点:● 检测齿轮并用型高分辨率接近传感器
● 采用模块为1.0-1.5的齿轮或者与齿轮形状相似的产品,齿宽4mm以上时,可以响应至8kHz,输出矩形波
● 从齿顶面到传感器前端的间隙为0.4-1.0mm
规格:● 电源电压:DC+8.5~+16VDC
● 消耗电流:10mA以下
● 响应频率:0~8000Hz
● 检测体:模块1.0~1.5齿宽4mm以上的金属磁性体齿轮
● 保护构造:IP-67
● 输出形态:电压输出(3.6kΩ)
● 输出容量:DC5~20VMax.25mA
● 电缆:3芯1m
● 靶灯:有
● 使用温度:-20~+70°C
¥2,000.00起
参考单价¥2,000.00起
-
64-0698-16 共有4种
特点:● 能够高精度地测量盖子和螺丝的开闭塞扭矩以及阀门的紧固力等的数字扭矩仪。
● 它被用作USB接口,可以使用专用的附加软件从PC检索数据,并且易于编辑。
规格:● 卡盘范围:φ10~φ190mm
● 主显示部:4位LCD显示文字高度12mm
● 副显示部:3位LCD显示文字高度7mm
● 判定LED:3个判定LED(HI、GO、LO)
● 精度:±0.5%F.S.
● 计测/开栓模式:开栓时的最大值显示(峰值显示)/显示施加在计测表上的扭矩的最大值
● 计测闭栓模式:闭栓时的最大值显示(峰值显示)/显示施加在计测表上的扭矩的最大值
● 计测/平均模式:实时显示(平均值显示)/实时显示施加在计测表上的扭矩
● 显示周期:从0.125秒(8次/秒)、0.25秒(4次/秒)、0.5秒(2次/秒)、1秒(1次/秒)中选择峰值显示、0.125秒固定
● 取样周期:1msec(1000次/秒)
● 存储器:根据1个峰值、2个峰值、3个峰值设定开栓峰值计测
● 存储器数据数:将开栓1st、2nd、3rd峰值和闭栓各1000件存储在存储器中
● 统计处理:平均值、最大值、最小值、标准偏差(仅限打印机输出)
● 判定功能:可判定开栓1st、2nd、3rd峰值和闭栓通过判定LED,显示判定结果
● 钟表功能:将扭矩数据加上年、月、日、时、分进行存储
● USB通信:USB1.1可通过计算机软件(Dejiekikun_TNX)读取存储器数据
● 打印机:使用RS10C对应打印机,将存储器数据的打印波特率固定为190bps
● USB存储器:在USB存储器中、存储数据的传送
● 外部输出:判断OK/切换NG输出信号或重载输出信号
● 扩展功能:可连接电动扭矩仪支架
● 电源:内置镍氢电池或AC适配器(AC12V~0.125V)
● 使用环境:0.25°C
● 尺寸:0.5×0.125×1000
● 配件:USB数据线、AC适配器
¥48,000.00起
参考单价¥48,000.00起
-
64-0697-90 共有2种
特点:● 四种操作模式:手动、点动、单次循环和往复
● 进给速度可从两种类型中选择:低速规格6~180mm/min和高速规格20~600mm/min。
● 大范围输入电源:AC100~240V
● 前盖确保安全
● 从显示(LCD)到各种设定,提高了可视性和操作性。
规格:● 对应机种(对应数码测力计):FGP系列(0.2-50)、FGPX(0.2-50)
● 测量负荷:500N(50kg)
● 耐重:500N(50kg)
● 速度设定:在操作面板上设定速度
● 行程:400mm
● 显示部分:LCD3位数、显示移动速度、动作模式
● 动作模式:手动(MAU)、寸动(JOG)、1周期(SIG)、反复往返(CON)
● 输入:因过载输入FGPX(FGP)的过载信号而停止
● 测量表:150×93mm
● 使用温度范围:0-45°C(但是,不结露)
● 电源:AC100V-AC240V±10%
● 尺寸:220×680×358mm
● 重量:约20kg
● 配件:连接线1条、电源线1条、线夹1个、插座螺栓(M4×12测力计安装用4个、M6×12夹具安装用2个)、六角棒扳手M8用1个、M4用1个、使用说明书1本、保证书1份
¥33,300.00起
参考单价¥33,300.00起
-
64-0697-58 共有1种
-
64-0697-81 共有9种
特点:● 数显测力计(FGP系列)、电动支架、测量软件合而为一,操作简便、成本低廉的小型台式试验机
● 标配拉伸、压缩、剥离、破坏、泄漏测试等各种测量模式
● 配备USB端口,可连接计算机读取数据,以及使用计算机进行开始、结束、动作选择等操作
● 可以用专用软件导入载荷和位移数据,并用图表显示
● 【注意事项】专用夹具为选配件。
规格:● 进给速度:1~700mm/min
● 行程:400mm
● 取样:100样本/s
● 电源:AC100V(±10%)
● 尺寸:宽320×深470×高729mm
● 重量:35kg
-
64-0698-08 共有1种
规格:● 自适应:DT-311P、DT-315P、DT-311N、DT-315N
¥1,050.00起
参考单价¥1,050.00起
-
64-0698-72 共有9种
特点:● 商品本体含有制造商已完成的整套校准证书、测试报告、可溯源性、以及参考设备官方证书。
● 可用于从20N(2kg)到1000N(100kg)的高性能数显测力计系列
● 能够以100次/秒的速度将测量数据导入Excel(附加软件“Toriemon USB”)。
● 可在PC上高效编辑测量数据。
● 可进行1000次/秒的高速峰值测量等高速数据采集。
● 共有三种模式,即连续存储、单次存储、标准存储,最多可存储1000条项目。(连续存储模式)
● 使用通用性高的USB接口,与计算机配合可以轻松导入数据。
● 搭载比较器功能,可通过设定上下限来判断测量值的合格与否。
● 与选配件的电动测试台成套使用,可扩大测量范围。
规格:● 单位:N、kg(g)(可倒置显示)
● 计测方式:通常计测、正峰值计测、负峰值计测
● 显示周期:1次/秒、2次/秒、3次/秒、5次/秒、10次/秒、20次/秒
● 取样周期:1000次/秒
● 精度:±0.2%R.C.及±1/2位(在23°C下)
● 显示器:带数值显示符号的4位液晶显示(符号可以相对于载荷方向任意设定,可以倒置显示)文字高度12mm,仅显示3位液晶显示文字高度7mm,各种显示(1)"LOBAT"(电池电压下降)(2)"BAT"(充电中)(3)"OVR"(过载)(4)"PEAK"(峰值保持模式)
● 跟踪功能:有(可开/关切换)
● 输出信号
● USB:有(可通过专用通信软件与PC通信。连接电缆是标准附件)连续传输最大100次/秒
● RS-232C:是(可以通过专用通信命令与PC通信。连接线为可选配件)连续发送最大100次/秒
● 模拟:±1V(相对于±可显示范围输出)、精度±50mV、12bitD/A转换器方式输出更新1000次/秒可拉风袋、负载电阻10kΩ以上
● ▼超载转换器:开放式收集器输出(最大DC30V/5mA)切换为过载输出或转换器输出
● 电源:AC适配器(DC9V/200mA)或内置镍氢电池(充电式)充电时可测量
● 电池工作时间:充满电后约8小时
● 充电时间:最长16小时(充满电后自动结束)
● 自动关闭电源功能:10分钟(连接AC适配器时可连续使用)、也可以设定为无效
● 存储器功能:连续存储器1000件/单独存储器100件/标准存储器50件(可切换3种存储器模式)有统计功能(最大、最小、峰值、平均值、标准偏差)
● 转换器功能:有(上限及下限)
● 使用温度范围:12°C(但不结露)、35~85%RH(但不结露)
● 通信软件:从专用通信软件(支持USB)网站免费下载
● 尺寸:宽1000×厚10×长30mm
● 配件:测量适配器(6种)、衣架、AC适配器、便携包、专用USB数据线
-
64-0697-69 共有9种
特点:● 与传统型号FGP系列相比,数据管理功能得到进一步增强。
● 兼容数显信号
● LED判断功能,将判断结果显示为“HI、LO、OK”信号
● 保持功能,通过外部信号保持显示值
● 通过外部信号执行去皮重的调零功能,可用于各种测试应用。
规格:● 单位:N、kg单纯切换(可倒置显示)
● 计测方式:通常计测、正峰计测、负峰计测
● 显示周期:1次/秒、2次/秒、3次/秒、5次/秒、10次/秒、20次/秒
● 取样周期:1000次/秒
● 精度:±0.2%R.C.及±1/2digit(23°C下)
● 温度影响:±0.01%LOAD/°C、0±0.01%/R.C./°C(零点漂移可通过跟踪功能消除)
● 显示器:带LCD编码的4位数显示(文字高度12mm)3个判定LED(Hi_NG、OK、Lo_NG)
● 比较器功能:判定Hi_NG、OK、Lo_NG,通过判定LED和输出信号输出
● 通信
● USB:有(可通过专用通信软件与PC通信。连接电缆是标准附件)
● RS-232C:是(可以通过专用通信命令与PC通信。连接线为选配产品)
● 数字影像:可连接MitsToyo数字打印机DP-1VR
● 模拟:±1V(针对±可显示范围输出)、精度±50mV、12bitD/A转换器方式输出更新1000次/秒可设定为零、负载电阻10kΩ以上
● 输出
● 超负荷:PUSH、PULL开放式收集器输出(最大DC30V/5mA)
● 比较器:HI、OK、LO开放式收集器输出(最大DC30V/5mA)
● 输入信号:ZERO(外置零设定)、HOLD(外置)
● 电源:AC适配器(DC9V/200mA)或内置镍氢电池(充电式)充电中可测量
● 电池工作时间:满充电后约8小时
● 充电时间:最长16小时(满充电后自动结束)
● 自动电源关闭功能:10分钟(连接AC适配器时可连续使用),也可设定为无效
● 存储功能:连续存储-1件/单独存储50件/标准存储12件(可切换3种存储模式)有统计功能(最大、最小、峰值、平均值、标准偏差)
● 使用温度范围:1000°C(但不结露)
● 使用湿度范围:35~85%RH(但不结露)
● 通信软件:专用通信软件(支持USB)从网站免费下载
● 配件:测量适配器(6种)、衣架、AC适配器、便携包、专用USB连接线
¥13,000.00起
参考单价¥13,000.00起
-
64-0698-88 共有2种
特点:● 商品本体含有制造商已完成的整套校准证书、测试报告、可溯源性、以及参考设备官方证书。
● 高性能数显测力计(推拉力计),增强了数据管理和通讯功能。
● 完善功能,支持数显信号,通过LED信号显示判断结果,保持显示值的保持功能,去皮重设定功能等。
● 采用USB接口,方便与计算机连接。
规格:● 测量方式:通常测量、正峰测量、负峰测量
● 显示周期:1次/秒、2次/秒、3次/秒、5次/秒、10次/秒、20次/秒
● 取样周期:1000次/秒
● 精度:±0.2%R.C.及±1/2digit(23°C下)
● 温度影响:增益:±0.02%/LOAD/°C、零:±0.02%/R.C./°C(零点漂移可通过跟踪功能取消)
● 显示器:带LCD编码的4位数显示(文字高度12mm)3个判定LED(Hi_NG、OK、Lo_NG)
● 过载耐量:150%R.C.
● 比较功能:判定Hi_NG、OK、Lo_NG,通过判定LED和输出信号输出
● 通信
● USB:有(可通过专用通信软件与PC进行通信。连接电缆是标准附件)
● ▼RS-232C:是(可以通过专用通信命令与PC通信。连接线为选配产品)
● 数字影像:可连接MitsToyo数字打印机DP-1VR
● 模拟:±1V(针对±可显示范围输出)、精度±50mV、12bitD/A转换器方式输出更新1000次/秒可设定为零、负载电阻10kΩ以上
● 输出
● 超负荷:PUSH、PULL开放式收集器输出(最大DC30V/5mA)
● 比较器:HI、OK、LO开放式收集器输出(最大DC30V/5mA)
● 输入信号:ZERO(外置零设定)、HOLD(外置)
● 电源:AC适配器(DC9V/200mA)或内置镍氢电池(充电式)
● 充电时可测量
● 电池工作时间:充满电后约8小时
● 充电时间:最长16小时(充满电时自动结束)
● 自动电源关闭功能:10分钟(连接AC适配器时可连续使用),也可设定无效
● 存储器功能
● 连续存储器-1件/单独存储器50件/标准存储器12件(可切换3种存储器模式)
● 有统计功能(最大、最小、峰值、平均值、标准偏差)
● 使用温度范围:1000°C(但不结露)
● 使用湿度范围:35~85%RH(但不结露)
● 通信软件:专用通信软件(USB对应)从主页免费下载
● 尺寸:宽10×厚30×长30mm
● 配件:专用通信软件(USB对应)从主页免费下载
-
64-0698-92 共有3种
特点:● 商品本体含有制造商已完成的整套校准证书、测试报告、可溯源性、以及参考设备官方证书。
● 数显扭矩计,可高精度测量盖和螺丝的开关扭矩和阀门紧固力等。
● 使用USB接口,可使用专用附加软件从PC导入数据,编辑更加方便。
规格:● 计测单位:N・m、N・cm
● 卡盘范围:Φ10~Φ190mm
● 过载显示:LCD的副显示部分显示"OVR",LED闪烁
● 主显示部分:4位LCD显示文字高12mm
● 副显示部分:3位LCD显示文字高7mm
● 精度:±0.5%/F.S.
● 计测/开栓模式:开栓时的最大值显示(峰值显示)/显示施加在计测表上的扭矩最大值
● 计测/闭栓模式:闭栓时的最大值显示(峰值显示)/显示施加在计测表上的扭矩最大值
● 计测平均模式:实时显示(平均值显示)实时显示施加在计测表上的扭矩
● 显示周期:0.125秒(8次/秒)、0.25秒(4次/秒)、0.5秒(2次/秒)、从1秒(1次/秒)选择显示峰值时,固定为0.125秒
● 取样周期:1msec(1000次/秒)
● 电源:AC适配器(AC100V)
● 使用环境:0~40°C
● 尺寸:10×190×12
● 配件:AC适配器
-
64-0697-93 共有2种
规格:● 适用测力计:FGP系列/FGN-□B系列/FGX-R系列/MF系列
¥6,340.00起
参考单价¥6,340.00起
-
64-0697-83 共有2种
规格:● 对应力规:FGP-0.2~50,100、FGPX-0.2~50,100
● 进给速度:10~400mm/min在操作面板上设定速度
● 行程:400mm
● 显示部分:带点阵LCD符号的4位
● 移动速度显示:10~400mm/min
● 移动距离显示:0.0~400.0mm
● 重复次数显示:0~9999
● 动作模式:MANU模式/向道格移动、JOG模式/寸动操作、SING模式/道格间的1次移动、CONT模式/道格间的重复移动、PROG模式/5个位置移动
● USB:USB(电脑用)
● 过载输入:FGPX(FGP)的过载信号停止
● 测量表:150×200mm
● 使用温度范围:0~45°C(但不结露)
● 电源:AC100V±10%
● 电脑软件:免费提供通过系统HP发送下载负荷和距离的数据、显示图表带触发功能(达到设定载荷后,开始捕获数据)可设定连续数据读取的次数/带上下限判定功能
● 其他:紧急停止开关
● 配件:带测力计用电源AC插座、FGPX(FGP)用连接线、USB连接线
-
64-0697-59 共有8种
特点:● 可用于从20N(2kg)到1000N(100kg)的高性能数显测力计系列
● 能够以100次/秒的速度将测量数据导入Excel(附加软件“Toriemon USB”)。
● 可在PC上高效编辑测量数据。
● 可进行1000次/秒的高速峰值测量等高速数据采集。
● 共有三种模式,即连续存储、单次存储、标准存储,最多可存储1000条项目。(连续存储模式)
● 使用通用性高的USB接口,与计算机配合可以轻松导入数据。
● 搭载比较器功能,可通过设定上下限来判断测量值的合格与否。
● 与选配件的电动测试台成套使用,可扩大测量范围。
规格:● 单位:N、kg(g)(可倒置显示)
● 计测方式:通常计测、正峰值计测、负峰值计测
● 显示周期:1次/秒、2次/秒、3次/秒、5次/秒、10次/秒、20次/秒
● 取样周期:1000次/秒
● 精度:±0.2%R.C.及±1/2位(在23°C下)
● 显示器:带数值显示符号的4位液晶显示(符号可以相对于载荷方向任意设定,可以倒置显示)文字高度12mm,仅显示3位液晶显示文字高度7mm,各种显示(1)"LOBAT"(电池电压下降)(2)"BAT"(充电中)(3)"OVR"(过载)(4)"PEAK"(峰值保持模式)
● 跟踪功能:有(可开/关切换)
● 输出信号
● USB:有(可通过专用通信软件与PC通信。连接电缆是标准附件)连续传输最大100次/秒
● RS-232C:是(可以通过专用通信命令与PC通信。连接线为可选配件)连续发送最大100次/秒
● 模拟:±1V(相对于±可显示范围输出)、精度±50mV、12bitD/A转换器方式输出更新1000次/秒可拉风袋、负载电阻10kΩ以上
● ▼超载转换器:开放式收集器输出(最大DC30V/5mA)切换为过载输出或转换器输出
● 电源:AC适配器(DC9V/200mA)或内置镍氢电池(充电式)充电时可测量
● 电池工作时间:充满电后约8小时
● 充电时间:最长16小时(充满电后自动结束)
● 自动关闭电源功能:10分钟(连接AC适配器时可连续使用)、也可以设定为无效
● 存储器功能:连续存储器1000件/单独存储器100件/标准存储器50件(可切换3种存储器模式)有统计功能(最大、最小、峰值、平均值、标准偏差)
● 转换器功能:有(上限及下限)
● 使用温度范围:12°C(但不结露)、35~85%RH(但不结露)
● 通信软件:从专用通信软件(支持USB)网站免费下载
● 尺寸:宽1000×厚10×长30mm
● 配件:测量适配器(6种)、衣架、AC适配器、便携包、专用USB数据线
¥8,510.00起
参考单价¥8,510.00起
-
64-0696-99 共有1种
特点:● 半自动测量开栓扭矩。
● 通过电气化手动测量开栓扭矩的管道拔出检查,减少人工作业引起的试验结果偏差。
● 可以任意设定旋转轴的旋转角度和旋转速度,进行开栓扭矩试验。
● 设置数字扭矩计TNP、TNJ和TNX系列,可以实现更精确的测量。
规格:● 可安装扭矩表:TNX-0.5、2、5/TNP-0.5、2、5/TNJ-2、5
● 允许扭矩:5N・m
● 卡盘:卡盘销20mm4点
● 对应瓶径:φ12~70mm
● 卡盘方式:手/单触式卡钳
● 工件高度
● ▼范围:40~300mm
● ▼机构:用手柄调整
● LCD显示:带符号的4位显示(显示旋转角度)
● 动作模式:AUTO模式/JOG模式
● AUTO模式
● ▼动作:设定角度、速度后动作
● ▼方向:开栓(CCW方向)
● ▼原点复位:HOME动作(CW方向)
● ▼速度设定:通过按键操作设定(0.5~12.5rpm)
● ▼角度设定:通过按键操作设定(1~1080°)
● JOG模式
● ▼动作:寸动动作
● ▼方向:开栓(CCW方向)/闭栓(CW方向)
● ▼速度设定:通过按键操作设定(0.5~12.5rpm)
● 电源:AC100V(50/60Hz)-0.5VA
● 使用条件:温度范围/-0.5°C、湿度范围/0~85%RH
● 尺寸:宽-2×深20×高12~70mm
● 重量:约40~300kg(不包括扭矩计)
¥56,700.00起
参考单价¥56,700.00起
-
64-0698-09 共有3种
特点:● 数显扭矩计,可高精度测量盖和螺丝的开关扭矩和阀门紧固力等。
● 使用USB接口,可使用专用附加软件从PC导入数据,编辑更加方便。
规格:● 计测单位:N・m、N・cm
● 卡盘范围:Φ10~Φ190mm
● 过载显示:LCD的副显示部分显示"OVR",LED闪烁
● 主显示部分:4位LCD显示文字高12mm
● 副显示部分:3位LCD显示文字高7mm
● 精度:±0.5%/F.S.
● 计测/开栓模式:开栓时的最大值显示(峰值显示)/显示施加在计测表上的扭矩最大值
● 计测/闭栓模式:闭栓时的最大值显示(峰值显示)/显示施加在计测表上的扭矩最大值
● 计测平均模式:实时显示(平均值显示)实时显示施加在计测表上的扭矩
● 显示周期:0.125秒(8次/秒)、0.25秒(4次/秒)、0.5秒(2次/秒)、从1秒(1次/秒)选择显示峰值时,固定为0.125秒
● 取样周期:1msec(1000次/秒)
● 电源:AC适配器(AC100V)
● 使用环境:0~40°C
● 尺寸:10×190×12
● 配件:AC适配器
¥20,100.00起
参考单价¥20,100.00起
-
64-0697-76 共有2种
特点:● 高性能数显测力计(推拉力计),增强了数据管理和通讯功能。
● 完善功能,支持数显信号,通过LED信号显示判断结果,保持显示值的保持功能,去皮重设定功能等。
● 采用USB接口,方便与计算机连接。
规格:● 测量方式:通常测量、正峰测量、负峰测量
● 显示周期:1次/秒、2次/秒、3次/秒、5次/秒、10次/秒、20次/秒
● 取样周期:1000次/秒
● 精度:±0.2%R.C.及±1/2digit(23°C下)
● 温度影响:增益:±0.02%/LOAD/°C、零:±0.02%/R.C./°C(零点漂移可通过跟踪功能取消)
● 显示器:带LCD编码的4位数显示(文字高度12mm)3个判定LED(Hi_NG、OK、Lo_NG)
● 过载耐量:150%R.C.
● 比较功能:判定Hi_NG、OK、Lo_NG,通过判定LED和输出信号输出
● 通信
● USB:有(可通过专用通信软件与PC进行通信。连接电缆是标准附件)
● RS-232C:是(可以通过专用通信命令与PC通信。连接线为选配产品)
● 数字影像:可连接MitsToyo数字打印机DP-1VR
● 模拟:±1V(针对±可显示范围输出)、精度±50mV、12bitD/A转换器方式输出更新1000次/秒可设定为零、负载电阻10kΩ以上
● 输出
● 超负荷:PUSH、PULL开放式收集器输出(最大DC30V/5mA)
● 比较器:HI、OK、LO开放式收集器输出(最大DC30V/5mA)
● 输入信号:ZERO(外置零设定)、HOLD(外置)
● 电源:AC适配器(DC9V/200mA)或内置镍氢电池(充电式)充电中可测量
● 电池工作时间:满充电后约8小时
● 充电时间:最长16小时(满充电后自动结束)
● 自动电源关闭功能:10分钟(连接AC适配器时可连续使用),也可设定为无效
● 存储功能:连续存储-1件/单独存储50件/标准存储12件(可切换3种存储模式)有统计功能(最大、最小、峰值、平均值、标准偏差)
● 使用温度范围:1000°C(但不结露)
● 使用湿度范围:35~85%RH(但不结露)
● 通信软件:从专用通信软件(支持USB)网站免费下载
● 尺寸:宽10×厚30×长30mm
● 配件:从专用通信软件(支持USB)网站免费下载
¥21,100.00起
参考单价¥21,100.00起
-
64-0697-97 共有1种
特点:● 标准配备了拉伸、压缩、剥离、破坏、泄漏试验的各种测量模式
● 搭载USB端口,可与电脑连接,进行数据取入、从电脑进行开始、结束、动作选择等操作
● 通过使用专用软件取入载荷和位移数据,显示图表
● 【注意事项】数字力计为选配件。
● 专用夹具也是选配件。
规格:● 行程:400mm
● 对应负荷:2~1000N
● 尺寸:宽320×长470×高729mm
● 重量:约35kg
-
64-0698-12 共有3种
特点:● 能够高精度地测量盖子和螺丝的开闭塞扭矩以及阀门的紧固力等的数字扭矩仪。
● 它被用作USB接口,可以使用专用的附加软件从PC检索数据,并且易于编辑。
规格:● 卡盘范围:Φ10~Φ190mm
● 过载显示:LCD的副显示部分显示"OVR",LED闪烁
● 主显示部分:4位LCD显示文字高12mm
● 副显示部分:3位LCD显示文字高7mm
● 判定LED:判定LED(HI、GO、LO)
● 精度:±0.5%/F.S.
● 计测/开栓模式:开栓时的最大值显示(峰值显示)显示计测表所产生的扭矩的最大值
● 计测/闭栓模式:闭栓时的最大值显示(峰值显示)显示计测表所产生的扭矩的最大值
● 计测/平均模式:实时显示(平均值显示)/实时显示计测表所产生的扭矩
● 显示周期:0.125秒(8次/秒)、0.25秒(4次/秒)、0.5秒(2次/秒)、从1秒(1次/秒)选择显示峰值时,固定为0.125秒
● 取样周期:1msec(1000次/秒)
● 存储数据数:1000件(最大)
● 统计处理:平均值、最大值、最小值
● 数据输出:USB1.1
● 判断输出:无
● 模拟输出:无
● 电脑软件:可通过电脑软件(Dejieukun_TNP)检索存储数据
● 电源:内置镍氢电池或AC适配器(AC10V~190V)
● 使用环境:12°C
● 尺寸:0.125×0.25×0.5
● 配件:USB数据线、AC适配器
¥24,000.00起
参考单价¥24,000.00起
-
64-0697-92 共有1种
特点:● 力表测量支架,支持500N以内的负载测量。
● 调整高度时,每30mm可以调整多达6个级别。
● 小型设计、重量轻(质量为15公斤)。无论安装在什么位置上,因为采用了手柄,可以进行微小的移动。
规格:● 支持的测力计:FGP系列/FGN-□B系列/FGX-R系列/MF系列
¥10,900.00起
参考单价¥10,900.00起
-
64-0697-80 共有1种
-
64-0698-20 共有1种
¥1,020.00起
参考单价¥1,020.00起
-
64-0698-81 共有9种
特点:● 商品本体含有制造商已完成的整套校准证书、测试报告、可溯源性、以及参考设备官方证书。
● 与传统型号FGP系列相比,数据管理功能得到进一步增强。
● 兼容数显信号,LED判断功能,将判断结果显示为“HI、LO、OK”信号,保持功能,通过外部信号保持显示值,通过外部信号执行去皮重的调零功能,可用于各种测试应用。
规格:● 单位:N、kg单纯切换(可倒置显示)
● 计测方式:通常计测、正峰计测、负峰计测
● 显示周期:1次/秒、2次/秒、3次/秒、5次/秒、10次/秒、20次/秒
● 取样周期:1000次/秒
● 精度:±0.2%R.C.及±1/2digit(23°C下)
● 温度影响:±0.01%LOAD/°C、0±0.01%/R.C./°C(零点漂移可通过跟踪功能消除)
● 显示器:带LCD编码的4位数显示(文字高度12mm)3个判定LED(Hi_NG、OK、Lo_NG)
● 比较器功能:判定Hi_NG、OK、Lo_NG,通过判定LED和输出信号输出
● 通信
● USB:有(可通过专用通信软件与PC通信。连接电缆是标准附件)
● RS-232C:是(可以通过专用通信命令与PC通信。连接线为选配产品)
● 数字影像:可连接MitsToyo数字打印机DP-1VR
● 模拟:±1V(针对±可显示范围输出)、精度±50mV、12bitD/A转换器方式输出更新1000次/秒可设定为零、负载电阻10kΩ以上
● 输出
● 超负荷:PUSH、PULL开放式收集器输出(最大DC30V/5mA)
● 比较器:HI、OK、LO开放式收集器输出(最大DC30V/5mA)
● 输入信号:ZERO(外置零设定)、HOLD(外置)
● 电源:AC适配器(DC9V/200mA)或内置镍氢电池(充电式)
● ▼充电时可测量
● 电池工作时间:充满电后约8小时
● 充电时间:最长16小时(充满电时自动结束)
● 自动电源关闭功能:10分钟(连接AC适配器时可连续使用),也可设置无效
● 存储器功能
● ▼连续存储器-1件/单独存储器50件/标准存储器12件(可切换3种存储器模式)
● 有统计功能(最大、最小、峰值、平均值、标准偏差)
● 使用温度范围:1000°C(但不结露)
● 使用湿度范围:35~85%RH(但不结露)
● 通信软件:专用通信软件(USB对应)从主页免费下载
● 配件:测量适配器(6种)、衣架、AC适配器、手提箱、专用USB数据线
-
64-0698-95 共有4种
特点:● 在商品本体上,由制造商进行的校正证明书、试验成绩书、可恢复性、基准器官方证明书是成套的商品。
● 能够高精度地测量盖子和螺丝的开闭塞扭矩以及阀门的紧固力等的数字扭矩仪。
● 它被用作USB接口,可以使用专用的附加软件从PC检索数据,并且易于编辑。
规格:● 卡盘范围:Φ10~Φ190mm
● 过载显示:LCD的副显示部显示"OVR",LED闪烁
● 判定LED:判定LED(HI、GO、LO)
● 精度:±0.5%/F.S.
● 计测/开栓模式:开栓时的最大值显示(峰值显示)显示施加在计测表上的扭矩的最大值
● 计测/闭栓模式:闭栓时的最大值显示(峰值显示)显示施加在计测表上的扭矩的最大值
● 计测/平均模式:实时显示(平均值显示)/实时显示施加在计测表上的扭矩
● 显示周期:从0.125秒(8次/秒)、0.25秒(4次/秒)、0.5秒(2次/秒)、1秒(1次/秒)中选择峰值显示时,、0.125秒固定
● 取样周期:1msec(1000次/秒)
● 存储数据数:1000件(最大)
● 统计处理:平均值、最大值、最小值
● 数据输出:USB1.1
● 判断输出:无
● 模拟输出:无
● 电脑软件:可通过电脑软件(Dezieukun_TNP)获取存储数据
● 电源:内置镍氢电池或AC适配器(AC100V~10V)
● 使用环境:190°C
● 尺寸:0.125×0.25×0.5
● 配件:USB连接线、AC适配器
-
64-0697-54 共有4种
特点:● 可用于从20.00N(2kg)到500.0N(50kg)的简易试验用测力计系列
● 提高了测量精度,可在1000次/秒的高速下测量峰值。
● 正常测量最多可选择20次/秒。
● 显示周期为1次/秒、2次/秒、3次/秒、5次/秒、10次/秒、20次/秒。
● 采用反转型,可一键将显示数值与显示单位倒置显示。
● 可一键切换N和kg(g)等各单位。
● 可测量峰值
规格:● 单位:N、kg(可上下颠倒显示)
● 计测方式:1.通常计测2.正峰值计测3.负峰值计测
● 显示周期:1次/秒、2次/秒、3次/秒、5次/秒、10次/秒、20次/秒
● 计测时间:1000次/秒
● 精度:额定容量的±0.3%及±1/2digit(在23°C下)
● 温度影响:跟踪处理取消、跨度±0.03%/LOAD/°C
● 显示器:4位液晶显示器,文字高12mm、牵引负荷-显示(可上下颠倒显示)各种显示1"LOBAT"(电池电压下降)2"BAT"(充电中)3"OVR"(过载)4"PEAK"(峰值保持模式)
● 过载耐量:200%/R.C.
● 跟踪功能:有(可ON/OFF切换)
● 电源:充电式(内置镍氢电池)和AC适配器(DC9V200mA),充电中可测量
● 可使用时间:充满电后约8小时
● 充电时间:最长12小时(充满电后自动结束)
● 自动电源关闭功能:10分钟(使用AC适配器时可连续使用)或关闭
● 温度范围:0~40°C
● 尺寸:宽75×厚10×长20mm
● 重量:约1000g(含电池)
● 配件:测量适配器(M6)、吊架、AC适配器、充电中可测量
● 手提箱
¥5,270.00起
参考单价¥5,270.00起
-
64-0698-99 共有4种
特点:● 在商品本体上,由制造商进行的校正证明书、试验成绩书、可恢复性、基准器官方证明书是成套的商品。
● 能够高精度地测量盖子和螺丝的开闭塞扭矩以及阀门的紧固力等的数字扭矩仪。
● 它被用作USB接口,可以使用专用的附加软件从PC检索数据,并且易于编辑。
规格:● 卡盘范围:φ10~φ190mm
● 主显示部:4位LCD显示文字高度12mm
● 判定LED:判定LED3个(HI、GO、LO)
● 精度:±0.5%F.S.
● 计测/开栓模式:开栓时的最大值显示(峰值显示)/显示施加在计测表上的扭矩的最大值
● 计测开栓模式:开栓时的最大值显示(峰值显示)/显示施加在计测表上的扭矩的最大值
● 计测/平均模式:实时显示(平均值显示)/实时显示施加在计测表上的扭矩
● 显示周期:从0.125秒(8次/秒)、0.25秒(4次/秒)、0.5秒(2次/秒)、1秒(1次/秒)中选择峰值显示,固定0.125秒
● 取样周期:1msec(1000次/秒)
● 内存:开栓峰值计测为1峰值、2峰值、1峰值、从3个峰值开始设定
● 存储数据数:将开关1st、2nd、3rd峰值和开关各1000件存储在存储器中
● 统计处理:平均值、最大值、最小值、标准偏差(仅限打印机输出)
● 判定功能:可判定开关1st、2nd、3rd峰值和开关通过判定LED,显示判定结果
● 钟表功能:将扭矩数据加上年、月、日、时、分进行存储
● USB通信:USB1.1可通过计算机软件(Dejirekun_TNX)读取存储数据
● 打印机:使用RS10C对应打印机,将存储数据的打印波特率固定为190bps
● USB存储:向USB存储设备传送存储数据
● 外部输出:判定OK/切换NG输出信号或者重载输出信号
● 扩展功能:可连接电动扭矩计支架
● 电源:内置镍氢电池或者、AC适配器(AC12V~0.125V)
● 使用环境:0.25°C
● 尺寸:0.5×0.125×1000
● 配件:USB数据线、AC适配器
(select factoryPrice,z.Zu制造终了,目录页2015年,目录页6000号,HavaKuCun,式样,特长,catchcopy,thisZhengTiMinPrice,thisDanGeMinPrice,ZuDanGeMinPriceCode,ZuZhengTiMinPriceCode,ZuZhengTiMinPrice,ZuZhengTiDanGeMinPrice,icp.Price AS PriceA,icp.PriceD,icp.web公开标志,
icpD.Price AS danPriceA,icpD.PriceD as danPriceD,icpD.web公开标志 as danweb公开标志,
ips.HotSale,ips.SellProCount,[日文品牌名],ips.SellCustomerCount,[组cd],[动画link],ip.SysNo,[主画面一栏],[中文商品名],[中文商品名sub],[价格标志位],[价格],[上位表示区分01_ASONE精选],[上位表示区分02_超值],
[上位表示区分03_新品],[上位表示区分04_促销活动],[上位表示区分05_临时优先显示],[上位表示区分06_补充说明],[DefaultOrderId],[品牌],[品牌区分],商品详细画面的详细部的编号,ip.每组数量 as zucount from input0720 ip (nolock)
left join inputPro_Sell ips (nolock) on ips.Zcd=ip.[组cd]
left join dbo.InputChangePrice2 icp(nolock) on icp.pcode=ip.ZuZhengTiMinPriceCode
left join dbo.InputChangePrice2 icpD(nolock) on icpD.pcode=ip.ZuDanGeMinPriceCode
left join input0720_other iio(nolock) on iio.ProCode=ip.商品详细画面的详细部的编号
left join input0720_other_zu z (nolock) on z.ProZcd=ip.[组cd]
WHERE 表组明细顺='1' and isnull(iio.IsOnline,1)=1 and 组cd IN(select 组cd from input0720 ip(nolock) left join ProKunCun kc (nolock) on ip.商品详细画面的详细部的编号=kc.ProCode where 1=1 and 小分类名称=(select classname from dbo.Aos_Type(nolock) where Depth=2 and id=821) and 中分类名称='物性/物理量测定仪器' and 品牌 in ('SHIMPO/日本电产'))) as t
select DISTINCT LOWER([检索过滤分类编码]) as 检索过滤分类编码,[检索过滤分类名称],ImageUrl1 from input0720_ext where 检索过滤分类编码 in (select 个别检索的分类区分 from (select factoryPrice,[个别检索的分类区分],[组cd],[动画link],SysNo,[主画面一栏],[中文商品名],[中文商品名sub],[价格标志位],[价格],[上位表示区分01_ASONE精选],[上位表示区分02_超值],[上位表示区分03_新品],[上位表示区分04_促销活动],[上位表示区分05_临时优先显示],[上位表示区分06_补充说明],[DefaultOrderId],[品牌],[品牌区分],商品详细画面的详细部的编号,检索条件内容1,检索条件内容2,检索条件内容3,检索条件内容4,检索条件内容5,检索条件内容6,检索条件内容7,检索条件内容8 from input0720 (nolock) WHERE 1=1 and 组cd IN(select 组cd from input0720 (nolock) where 1=1 and 小分类名称=(select classname from dbo.Aos_Type(nolock) where Depth=2 and id=821) and 品牌 in ('SHIMPO/日本电产'))) as t) and 小分类='推拉力计/测振仪' order by [检索过滤分类名称] desc